AW Conventional Detector

Conventional photoelectric smoke detector

Item	Parameters
Operating Voltage Range:	9 to 32 VDC Volts Non-polarized
Standby Current:	≤100µA @ 24 VDC

Maximum Alarm Current (LED on: )	≤55mA @ 24 VDC
Operating Humidity Range:	10% to 93% Relative Humidity, Non-condensing
Operating Temperature Range:	14°F to 120°F (-10°C to 49°C)
Adjustable Sensitivity:	1-2.5%/FT
Height:	2.2˝ (55 mm) installed in Base
Diameter:	4.0˝ (103 mm)
Weight:	5.5 oz. (155 g)

Conventional fix temperature heat detector

Model No.: AW-CTD805

Item	Parameters
Height:	2.2˝ (55 mm) installed in Base
Diameter:	4.0˝ (103 mm)
Weight:	5.5 oz. (155 g)
Installation Temperatures:	14°F to 122°F (-10°C to50°C)
Operating Humidity Range:	10% to 93% Relative Humidity Non-condensing
Operating Voltage Range:	9 to 28VDC Volts Non-polarized
Standby Current:	40µA @ 24 VDC
Maximum Alarm Current (LED on: )	≤30mA @ 24 VDC
Fixed Temperature Rating:	135°F (57°C)

Conventional smoke and heat combined detector

Model No.: AW-CSH202

Item	Parameters
Operating Voltage Range:	9 to 28VDC Volts Non-polarized
Standby Current:	≤60µA @ 24 VDC
Maximum Alarm Current (LED on: )	≤30mA @ 24 VDC
Operating Humidity Range:	10% to 93% Relative Humidity, Non-condensing
Operating Temperature Range:	14°F to 120°F (-10°C to 49°C)
Smoke    Sensitivity:	1.06±.26%FT.
Fixed Temperature Rating:	135°F (57°C)
Rate of Rise Detection:	Responds to greater than 15°F/min
Height:	2.2˝ (55 mm) installed in Base
Diameter:	4.0˝ (103 mm)
Weight:	5.5 oz. (155 g)

UV flame detector

AW-FD602-UV

SPECIFICATIONS

Operating Voltage Range:                    12 to 30 VDC Volts

Standby Current:                                  ≤10 mA @ 24 VDC Alarm Current                                      ≤30 mA @ 24 VDC Spectrum:                                           180~290nm

Detection Angle:                                 110 degree

Detection Sensitivity:                         Grade I, 25m@flame (Container 33cmX33cm,Height 5cm with 2Kg ethanol )

Relay Contact Load:                            1A@DC24V

Normal Status:                                     LED blinking in 5 seconds interval

Alarm Status:                                       LED lit steady

Protection rating:                                  IP 32

Operating Humidity Range:                10% to 93% Relative Humidity, Non-condensing

Operating Temperature Range:          -10°C to 50°C (14°F to 122°F) Height:                                                 1.8˝ (45 mm) installed in Base Diameter:                                              4.0˝ (103 mm)

Weight:                                                 5.4 oz. (153g)

AW Conventional

Conventional fire alarm control panel

Introduction:

1.    AW-CFP2166 series conventional fire alarm panel is designed based on EN54 part 2&4 standard.

2.    It is modularized design, the panel can extend from 1 zone to 32 zones easily.

3.    It has 2 level control mode by a lock

4.    It has 24VDC and 5VDC power supply output.

5.    It has FIRE and FAULT signal output.

6.    It has 2 general sounders output.

7.    Each zone has 1 circuit detectors input .

8.    Each zone can be disable by a button.

9.    It has RESET button to reset the panel.

10.  It has SILENCE button to stop BUZZER and SOUNDERS.

11.  It has EVACUATE button to start a manual fire alarm immediately.

12.  It has battery low protection function, when battery voltage lower than 21VDC, battery will be cut off automatically until the mains power is on.

13.  It has an optional GSM module for fire alarm by SMS .

14.  It is economic, user-friendly and easy maintenance.

ITEM	1Zone panel	2Zone panel	4-8 Zone panel	12-32 Zone panel
Model No.	AW-CFP2166-01	AW-CFP2166-02	AW-CFP2166-04 -8	AW-CFP2166-12- 32
Power specification
Mains supply voltage	110VAC or 240VAC
Internal power supply	27.2VDC
Total output current limited	500mA @ 240VAC	500mA @ 240VAC	3A @ 240VAC	3A @ 240VAC
Main supply monitor for fault	Yes
Battery protection for low voltage	Yes
Batteries (default configuration)	12V2AH*2
Detector circuit specification
Number of circuit	1	2	4-16	4-32
Line fault monitor for open circuit	Yes
Line fault monitor for short circuit	Yes
Line fault monitor for detector removal	Yes, if End of Line Monitor Unit fitted in place of End of Line Resistor
End of Line device	6.8k Ω ,5% tolerance, 0.25W (colour code-blue,grey,red,gold)
Detector continuity diodes	Silicon 1N4001 or Schottky type (required if End of Line Monitor Unit fitted to give Detector Removal Fault)
Call point resistor value	470 to 680  Ω , 0.225 or 0.5 watt
Maximum number of smoke/heat detectors per zone	20 (based on a total detector current of 2mA, each detector consuming 100μ A).Note: if End of Line Monitor Unit is fitted, for correct operation maxmum voltage drop must not exceed 12 volts.
Maximum number of manual call points per zone	No limit
Sounder circuit specification
Number of general circuits	2
End of line resistor value	6.8k Ω ,5% tolerance, 0.25W (colour code-blue,grey,red,gold)
Line fault monitor for open circuit	Yes
Line fault monitor for short circuit	Yes
Outputs fused AT	400mA
Maximum number of bells @ 20mA of each sounder output	20
Fuses
Battery fuse	1.5A F 20mm
Sounder outputs	500mA F 20mm
Fire and fault output